How to choose a downstem and bowl

The downstem and the bowl are the removable glass parts at the top of many glass bongs. The downstem is the narrow glass tube that runs from the joint down into the water chamber, and the bowl is the small glass cup that sits on top. Both parts can be replaced separately, but they have to fit the bong and each other. This guide goes through what to check before choosing a new part: joint size, male and female, angle, length, number of holes, glass thickness, handles and screens. It also explains when an adapter solves a mismatch. The difference between 14 and 18 mm as joint sizes is covered in more detail in a separate guide.

Joint sizes: 10, 14 and 18 mm

Glass parts are joined with ground joints. The joint is a slightly tapered glass surface that is frosted after grinding, so that the male and female parts sit tightly against each other without a seal. Sizes are given as 10, 14 and 18 mm, but the nominal measurements are about 10, 14.5 and 18.8 mm. The figure refers to the outer diameter of the male part at the joint. On many glass bongs the joint where the downstem goes in is 18 mm, while the downstem and bowl meet in a 14 mm joint. 10 mm is mostly found on small glass parts. The joint size is listed on the product page for each bong and each glass part, and it cannot be judged reliably from a photo.

Male and female

Every joint is either male or female. The male part is the one that goes in, and it has the ground surface on the outside. The female part receives it, and it has the ground surface on the inside. Two parts fit together when they have the same size and opposite gender, for example 14 mm male into 14 mm female. A typical downstem therefore has two measurements: a male part at the top that goes into the bong's joint, and a female opening that takes the bowl. This is often written as '18 mm male to 14 mm female' or simply 18/14. The bowl is then a 14 mm male. Read both measurements before ordering, since a bowl with a female joint will not fit a downstem that is also female.

Angle: 45° and 90°

The joint on the bong sits at a fixed angle that was set when the glass was blown. On most glass bongs with a removable downstem the joint enters the water chamber at a slant, and a straight downstem and an ordinary bowl simply follow that angle. The angle matters for parts that have their own joint on the outside, such as pre-chambers and angled adapters. Such parts are listed as 45° or 90°. A 90° part fits a joint that points straight up, and a 45° part fits a joint that sits at a slant. If the wrong angle is chosen, the part will lean and put strain on the joint. The angle is stated in the product description for parts where it matters.

Downstem length and how to measure it

The length of a downstem has to suit the bong. If it is too short, the lower end does not reach the water. If it is too long, the end can touch the bottom or a percolator, and the part can press against the glass when it is inserted. Length is usually given in centimetres or inches, and manufacturers do not always measure the same way. Compare it with the part that is already in the bong.

How to measure

Remove the downstem and lay it on a flat surface. Many manufacturers measure from the lower edge of the frosted, ground surface down to the tip, because that is the part that sits inside the bong. Others give the full length from the top of the female opening. Measure both ways and note the figures, so you can compare them with how the length is stated on the product page.

When the bong has no downstem

If the old downstem has broken, or the bong came without one, the distance can be measured inside the bong. Slide a thin stick through the joint until it reaches the bottom, mark where the stick meets the rim of the joint, and measure. Subtract about one to two centimetres so that the tip stays clear of the bottom and of any glass parts in the water chamber.

Number of holes and diffusers

A plain downstem has one open end. A diffused downstem has a closed end with several small holes or slits around the lower edge. The number ranges from a few holes to many narrow slits, and some models have a flat disc or a small dome at the bottom. A diffused downstem is a removable percolator, and the shapes are described in more detail in the guide to percolators. When choosing a part, the number of holes matters most for cleaning. More and narrower openings mean more surfaces where residue can build up, and they need longer in isopropyl alcohol and salt. A downstem with a single opening is the easiest to rinse clean and to see through.

Glass thickness

A downstem is thin and long, and it is often the glass part that breaks first. Thicker walls make the part heavier and more resistant to knocks, but no glass part is unbreakable. The glass thickness of downstems and bowls is stated less often than for the bong itself. Where it is given, it is in millimetres. Borosilicate glass handles temperature changes better than ordinary glass, but the parts should still not be moved straight from hot to cold water. A bowl often has thicker glass at the base, because it rests on its base when it is put down.

Bowls with or without a handle

Bowls come with and without a handle. A handle is a glass knob, a ring or a small stem that makes it easier to grip the bowl and lift it out of the joint. Without a handle the bowl is shorter, takes up less space and is easier to fit in a case. The size of the glass cup varies between models and is not always stated. Where the measurements are given, depth and inner diameter can be compared directly.

Screens

Some bowls have a built-in glass screen, meaning a glass base with one or more small holes, or a star-shaped glass plate at the bottom. Others have a single opening where a loose pipe screen can be placed. Pipe screens are small round meshes or perforated discs in metal or glass, available in several diameters. Measure the inner diameter of the cup and choose a screen that rests against the wall without having to be forced down. Metal screens are wear parts and are replaced when they have become bent or blocked.

Compatibility and adapters

Before ordering a new glass part, check four things: joint size, male or female, angle where it matters, and length for a downstem. When the size or gender does not match, glass adapters are available. An adapter has two joints, for example 18 mm female to 14 mm male, so that a 14 mm bowl can be used in an 18 mm joint. There are also adapters from 14 mm to 18 mm, and adapters that switch between male and female in the same size. Each adapter makes the setup slightly taller and adds a joint that has to be kept clean. Ground joints can get stuck once residue has built up. Clean the joints regularly, and twist gently rather than rocking when a part sits tight.

Frequently asked questions

How do I find the joint size of my bong?
The joint size is listed on the product page. If it is unknown, the outer diameter of a male part can be measured at the joint: about 14.5 mm means 14 mm, and about 18.8 mm means 18 mm.
Does an 18/14 downstem fit every bong with an 18 mm joint?
Only if the length also suits the bong. The joint size shows that the parts can be connected, but not that the tip ends up in the right place in the water chamber.
Can I use an 18 mm bowl in a 14 mm downstem?
Not directly. It needs an adapter from 14 mm to 18 mm with the right genders, and the bowl will then sit higher.
How do I loosen a glass part that is stuck?
Let the joint soak for a while in warm water or isopropyl alcohol, then twist gently. Do not use tools or knock the glass.