How to clean glass parts

Bowls, downstems, ash catchers and adapters are small glass parts with narrow channels and ground joints. Residue builds up faster in them than in the bong itself, and they are more prone to cracking. This guide covers only the parts: what loosens residue, how to avoid thermal shock, drying, storage and when it is time to replace them. Cleaning the bong itself is described in a separate guide.

Before you start: take the parts apart

Remove the bowl, downstem, ash catcher and any adapters and clips. Clean each part separately. If a part is stuck in its joint, let the glass reach room temperature and twist gently while lifting. If that does not help, a little warm water around the female joint can make the glass expand enough for the part to come loose. Never use pliers or force. Place the parts on a towel or a rubber mat while you work so they do not roll off the counter.

What loosens residue

Residue on glass comes off most easily with a solvent and something abrasive. What you choose depends on how much residue there is and how narrow the channels are.

Isopropyl alcohol and coarse salt

The most common method is isopropyl alcohol, often 90 per cent or higher, together with coarse salt. Put the parts in a sealable bag or box, add isopropyl alcohol until they are covered, and add a tablespoon of coarse salt. Shake gently. The salt scrubs while the alcohol dissolves the residue. Rinse thoroughly with lukewarm water afterwards. Isopropyl alcohol is highly flammable. Use it in a well-ventilated room and well away from open flames.

Soaking

Thick residue loosens more easily if the parts soak in isopropyl alcohol for a while before shaking. Leave them in a closed container. Glass handles soaking well, but silicone rings, plastic clips and metal parts should be removed first.

Warm water and washing-up liquid

Light residue and regular rinsing can often be handled with warm water and a little washing-up liquid. The water should be warm from the tap, not boiling.

Cleaners for glass

There are dedicated cleaners made for glass parts. Follow the instructions on the pack and rinse thoroughly afterwards.

Tools and method for each part

Pipe cleaners reach into narrow channels, such as the hole in the bottom of a bowl and the slits in a downstem. Small bottle brushes and tube brushes fit tubes and ash catchers. Cotton buds are useful in ground joints and around edges. Use brushes with soft or plastic bristles, since metal wire can scratch. Change pipe cleaners often, because they pick up residue and can spread it back onto the glass.

Bowl and slide

Shake the bowl in isopropyl alcohol and salt, and push a pipe cleaner through the hole in the bottom. Also clean the underside and the joint. A bowl with several small holes may need a slightly longer soak.

Downstem

The downstem has a narrow tube and often slits or holes at the bottom. Push a pipe cleaner through the whole length from both ends. Hold the part up to the light to check that the slits are open.

Ash catcher

An ash catcher has its own chamber and often a small percolator. Empty it, partly fill it with isopropyl alcohol and salt, close the openings with your fingers or with stoppers and shake. Rinse with clean water until the glass is clear.

Adapters and ground joints

Ground joints are matte and rough, and residue sticks to them easily. Wipe them with a cotton bud dampened with isopropyl alcohol. Clean joints are less likely to stick and seal better.

How to avoid cracks

Glass most often cracks from sudden temperature changes or impacts. Borosilicate glass withstands more than ordinary glass, but not everything. Do not put cold parts into boiling water, and do not rinse warm parts in cold water. Let the parts reach room temperature before cleaning, and use lukewarm water. Do not wash glass parts in a dishwasher, where they can knock against each other and face large temperature swings. Take extra care with thin points such as the slits on a downstem and the joins on an ash catcher. Shake calmly, and use a bag or box with some space around the parts.

Drying

Rinse the parts thoroughly with water until all isopropyl alcohol and salt is gone. Salt residue can scratch the joints. Let the parts dry on a clean towel or a drying rack with the openings facing down. Narrow tubes hold water for a long time, and a dry pipe cleaner through the channel speeds things up. Do not assemble the parts until they are completely dry, as moisture in ground joints can make them stick.

Storage

Store glass parts so they cannot roll or knock against each other. A box with compartments or a padded bag works well. Wrap thin parts such as downstems in a soft cloth. Keep the parts away from the edges of shelves and tables. If you have parts in several sizes, you can label the compartments 14 mm and 18 mm so the right part is easy to find.

When should a part be replaced?

Replace a glass part if it has cracks, chips on the rim or nicks in the ground joint. A crack can grow with temperature changes and make the part unstable. Also replace it if the residue will not come off, or if the slits on a downstem are still blocked after several cleanings. When you replace a part, check the joint size, gender and any angle. For a downstem, the length must also match the bong. Silicone rings and plastic clips wear out and can be replaced on their own.

Frequently asked questions

Can I wash glass parts in the dishwasher?
No. In a dishwasher the parts can knock against each other and face sudden temperature changes. Washing by hand with isopropyl alcohol and salt or warm water is gentler on the glass.
How often should glass parts be cleaned?
There is no fixed rule. Small parts with narrow channels clog faster than the bong and therefore need cleaning more often. Rinse lightly on a regular basis, and clean thoroughly when you see residue.
How do I loosen a stuck downstem?
Let the glass reach room temperature and twist gently while lifting. Warm water around the female joint can help. Never use tools or force.
Which salt can I use?
Coarse salt, such as coarse sea salt or coarse cooking salt. Fine salt dissolves too quickly to scrub well.