Checklist before you buy your first bong
Choosing your first bong is easier when you know what to look for. This checklist covers the measurements and features listed on product pages: height, glass thickness, material, base, joint size, percolator, replaceable parts, cleaning and storage. The aim is to help you compare models on equal terms and choose a bong that suits the place where it will stand and the amount of maintenance you want.
Height: what the measurement tells you
Height is usually given in centimetres from the bottom of the base to the top of the mouthpiece. It says little about the size of the water chamber, but a lot about where the bong can stand and be stored. A rough grouping is small bongs at approximately under 25 cm, medium bongs at approximately 25–35 cm and large ones above that. This grouping is not a standard, but it makes comparison easier. Measure the shelf or cupboard where the bong will stand before you decide. Remember that the bowl and downstem stick out to the side and make the bong wider than its base.
Height and cleaning
Tall, narrow tubes are harder to reach with a brush. A shorter bong with a wide opening is often easier to rinse and shake clean. Check the photos to see whether the neck is narrow or wide.
Glass thickness
Glass thickness is often given in millimetres, for example 3, 5, 7 or 9 mm. The figure usually refers to the wall of the main tube or the base, not to every part of the bong. Thicker glass withstands knocks better and makes the bong heavier and steadier. Thinner glass is lighter and often less expensive, but needs more care. If the thickness is not stated, the weight can give a clue: two bongs of the same height and different weight usually have different wall thickness. No glass thickness makes a bong unbreakable.
Material: borosilicate glass, silicone or acrylic
The material determines how robust the bong is, how easy it is to clean and how it looks over time. The three most common materials each have strengths and weaknesses.
Borosilicate glass
Borosilicate glass is laboratory glass that handles temperature differences better than ordinary glass. It is smooth and non-porous, and it can be cleaned with ordinary glass cleaners. You can easily see when it needs cleaning. The downside is that glass can break if dropped on a hard surface.
Silicone
Silicone bongs are soft and survive falls better than glass. Many can be taken apart, which makes cleaning simple. Silicone can absorb colour and odour over time, and the surface is not as smooth as glass. The bowl or an insert is often made of glass or metal.
Acrylic
Acrylic is light and inexpensive, but scratches more easily. Some solvents, including strong alcohol, can cause fine cracks in the surface. Follow the manufacturer's cleaning advice. The guide on glass versus acrylic goes into more detail.
Base and stability
A wide, flat base gives a lower centre of gravity, so the bong stands more steadily. Common base shapes are a straight bottom, a beaker shape with a wide bottom and a round chamber on a flat plate. A round bottom without a flat base is more likely to tip over. Also check whether the base is thicker than the rest of the glass. This is common on glass bongs and makes them less top-heavy. On smooth surfaces, a silicone mat or a tray under the bong can reduce the risk of sliding. If you have children or pets at home, good stability and a safe storage place matter even more.
Joint size: 14 or 18 mm
The bowl and downstem are attached with ground glass joints. The most common sizes are 14 mm and 18 mm, and 10 mm is found on small models. A joint can be male or female, and both size and gender should be stated on the product page. If you choose a bong with a common size, it is easier to find spare parts and accessories later. The downstem also has a length that must match the bong. Read the guide on 14 mm and 18 mm if you are unsure how to measure.
Clips and adapters
Joint clips hold the joints together. Adapters let you use parts of another size, but they make the setup taller and add one more joint to keep clean.
Percolator or not
A percolator is a fused glass part inside the bong that splits the airflow into several smaller streams. Common types are tree arm, showerhead, inline and honeycomb. A bong without a percolator has fewer parts and is the easiest to clean. Each percolator adds cavities where residue can collect, and it adds height and weight. The percolator is also a point where the glass is often thinner and more vulnerable to knocks. If you want as little maintenance as possible, a simple model without a percolator is a tidy starting point. The guide on percolator types explains the differences.
Replaceable parts
Check which parts are loose and which are fused. The bowl is almost always removable. The downstem is removable on many bongs, but fused on some. A removable downstem can be replaced if it cracks, and it can be taken out for cleaning. A fused downstem means fewer joints, but the whole bong must then be cleaned as one piece. An ash catcher is an extra part that sits between the bowl and the bong on some setups. If all loose parts come in common sizes, you can buy new ones without replacing the whole bong.
Cleaning and storage
Think about maintenance before you buy. Glass is usually cleaned with isopropyl alcohol and coarse salt, or with cleaners made for glass. A wide neck and few chambers make the job easier. Keep pipe cleaners and a bottle brush of a suitable size at hand. Dry the bong before you put it away. Store it upright in a stable place, away from the edges of shelves and tables, or in a padded bag or box. Loose parts can be stored separately so they do not knock against each other. The guide to cleaning a bong and the guide to cleaning glass parts explain the steps.
Frequently asked questions
- What height should a first bong be?
- There is no single answer. Choose a height that suits the place where the bong will stand and be stored. Medium bongs of approximately 25–35 cm are easy to handle and clean.
- Is thicker glass always better?
- Thicker glass withstands more knocks, but makes the bong heavier. It matters just as much that the glass is borosilicate and that the base is stable.
- Do I need a percolator?
- No. A percolator is a design choice. Without one, the bong is easier to clean and has fewer fragile points.
- How do I know which bowl fits?
- Check the joint size and gender on the product page, for example 14 mm female. The bowl must have the same size and the opposite gender.